C-22 Liquid Cleaner
C-22
Product Overview
Polymer Nation has created two cleaners for the care and maintenance of our coating systems. Our everyday cleaner is C-22 and our grease and crud-cutting cleaner is our C-23. Both formulas have been tested on our entire coatings line and can be recommended as effective, economical cleaners.
Uses
C-22 is a mild cleaner that is used to gently remove dirt and grime without leaving a film behind.
Preparation
The preparation method for each project is determined by a full understanding of the substrate to be coated, the chemistry of the coating system being used, the coating system thickness, and numerous other factors. The coating installer should fully read and understand ICRI Guideline NO.03732 and OSHA 29 CFR 1926.1153 before starting preparatory work. The aim, of preparing a substrate for coating applications, is to roughen the surface, remove weak layers, contaminants, dirt, debris and present a solid, clean, dry substrate for the primer. If unsure as to the level of preparation needed contact Polymer Nation at lab@polymernation.com.
The data below represents the most pertinent information needed by a professional installer to understand and efficiently install this material. The data was gathered at temperatures of 72-75 F and 30-50% RH. A wide array of independent and company test data has been compiled on this product but is too large to place on this Technical Data Sheet. Please direct inquiries for detailed test reports on this product to lab@polymernation.com.
C-22
| Description | Results | Notes |
| Kit Yield in Gallons | 5 | Material can be supplied in larger packaging upon request and with minimum quantities |
| Number of Components | 1 | |
| Mix Ratio Liquids by Volume | N/A | |
| Ideal Application Temperatures | 60F-90F | |
| Mixed Viscosity in cP@25C/77F | 30 | Warmer temperatures will reduce viscosity and lower temperatures will increase viscosity |
| Gel Time | N/A | Warmer temperatures will decrease gel time and lower temperatures will increase gel time |
| Dry to Touch | N/A | Warmer temperatures will reduce time and colder temperatures will increase time |
| Through Dry | N/A | Warmer temperatures will reduce time and colder temperatures will increase time |
| Dry to Walk | N/A | Warmer temperatures will reduce time and colder temperatures will increase time |
| Dry to Lightly Use | N/A | Warmer temperatures will reduce time and colder temperatures will increase time |
| Full Cure | N/A | Warmer temperatures will reduce time and colder temperatures will increase time |
| Pendulum (König) Hardness at 24 hours | N/A | Warmer temperatures will increase hardness |
| Pendulum (König) Hardness at 7 days | N/A | Warmer temperatures will shorten time to reach full hardness |
| Gloss @ 60 Degree Angle | N/A | Applying material close to dew point will decrease gloss and may result in an amine blush |
| VOC’s of Mixed Material | <0 g/L | EPA Method 24 |
| Color Scale per ASTM D1500 | N/A | Clear to slightly amber before colorants are introduced |
| Solids by Volume Mixed | >15% | Polymer Nation uses the strictest guidelines when determining volume solids of our coatings |
| Storage | 60F-90F | Store material between 60-90 degrees F in a protected dry location. |
| Odor | Subtle | Measuring odor offensiveness is difficult so experience with chemicals has been consulted here |
| Application Thickness in Mils | Both cleaners can be used at full strength or diluted 1:1 with water. | |
| Disposal | Dispose of material, containers, solvents, etc.per Federal, State and local guideline, rules and laws | |
| Available Colors | N/A | |
| Mixing & Installation | Both cleaners can be used in a floor scrubbing machine. Dilution may be required to avoid excessive foaming. | |
| Polymer Nation believes the information contained herein to be true and accurate. Information contained herein is for evaluation purposes only. |
||
