Category:
F-10 TD
F-10 TD Pigmented Epoxy Trowel Mortar
About the product
Product Overview
F-10 TD combines our pigmented, nonylphenol-free, epoxy resin (E1W), our blended cycloaliphatic reactant (H1.5) and our Trowel Aggregate PN 1324 to create the easiest troweling material available anywhere. This combination achieves an easily closed, pigmented epoxy mortar that can be walked on within a few hours. The cured material has high compressive strength (three times that of concrete) , great impact resistance and a broad range of resistance to chemical attack. It is virtually odor-free.
Uses
F-10 TD is primarily used as a fast setting epoxy overlay to protect and/or repair concrete. Because it is a mortar, it is the ideal material for sloping floors and creating ramps and transitions. It can also be used to fill deep pits, cracks and voids in concrete floors and walls.
Preparation
The coating installer should fully read and understand ICRI310.2R-2013 and OSHA 29 CFR 1926.1153 before starting preparatory work. The aim, of preparing a substrate for coating applications, is to roughen the surface, remove weak layers, contaminants, dirt, debris and present a solid, clean, dry substrate for the primer. If unsure as to the level of preparation needed contact Polymer Nation at techservice@polymernation.com
Product Details
For the most up-to-date product details, please view the Product Spec PDF below
PRODUCT PDFName
F-10 TD
Category
Kit Yield in Gallons
3 Gallons + 180 lbs. Aggregate (4x45 lb. bags)
N/A
Number of Mixes Per Kit
4
Mix: Part A - 0.5 gal, Part B - 0.25 gal, Part C - 45 lbs. Aggregate
Number of Components
3
N/A
Mix Ratio Liquids by Volume
2:1
Accuracy when mixing kits from bulk containers is critical. For mix ratio by weight contact Lab@polymerNation.com.
Ideal Application Temperatures
60-85°F
Verify that substrate temperature is above 5 degrees of dewpoint during application and cure of material to avoid a potential amine blush
Mixed Viscosity in cP@25C/77F
500-600 cP
Liquids only
Gel Time
15 min.
Warmer temperatures will decrease gel time and lower temperatures will increase gel time
Dry to Touch
1 Hour
Warmer temperatures will reduce time and colder temperatures will increase time
Through Dry
3-5 hrs
Warmer temperatures will reduce time and colder temperatures will increase time
Dry to Walk
4 Hours
Warmer temperatures will reduce time and colder temperatures will increase time
Dry to Lightly Use
8-12 hrs
Warmer temperatures will reduce time and colder temperatures will increase time
Full Cure
5-7 days
Warmer temperatures will reduce time and colder temperatures will increase time
Shore Hardness at 24 Hours
75
Shore D
Shore Hardness at 7 Days
75-80
Shore D
Gloss @ 60 Degree Angle
90+
Liquids only
VOC’s of Mixed Material
Near Zero; <50 g/L
EPA Method 24
Color Scale per ASTM D1500
N/A
N/A
Solids by Volume Mixed
100%
N/A
Storage
60F-90F
Store material between 60-90 degrees F in a protected dry location.
Odor
Subtle
N/A
Application Thickness in Mils
250 mils
1/4"
Coverage Per Mix
23 sq.ft./mix (4 mixes/kit)
Disposal
Dispose of material, containers, solvents, etc.per Federal, State and local guideline, rules and laws
N/A
Available Colors
White, Light Gray, Medium Gray, Warm Sun
Contact Polymer Nation for specialty colors
Mixing & Installation
See Technical Data Sheet or contact your local Polymer Nation Distributor
Other Product Names
Polymer Nation believes the information contained herein to be true and accurate. Information contained herein is for evaluation purposes only.
Product HIghlights
Exceptional Performance, Durability, and Safety in Every Application
.png)
Most commonly Serviced Markets
Although most our products can be used on any market, we see some common trends between certain products and certain markets.
Available Colors
If you don't see a color you like here, some custom colors can be available upon request. Please contact us for more details!
.jpg)
Product Documentation
PRODUCT PDF.png)
.png)
