Category:
F-41 SLQ
F-41 SLQ Clear UV Resistant 100% Solids Epoxy Slurry Terrazzo
About the product
Product Overview
F-41 SLQ consist of our clear, UV resistant epoxy and proprietary ultra-fine color quartz blends to create a 1/16″ decorative floor finish. This mixture allows the installer to blend 8 custom colors to create a unique floor finish. When PN 1321 Glint is added to the mix, the finish comes alive with light reflectivity. The cured material has high compressive strength (three times that of concrete) , great impact resistance and can be finish-coated with various epoxy and polyaspartic topcoats.
Uses
F-41 SLQ is primarily used to create an inexpensive, decorative and durable floor finish. With the appropriate conditions and a skilled installer it can be installed in 2 days after preparation.
Preparation
The coating installer should fully read and understand ICRI310.2R-2013 and OSHA 29 CFR 1926.1153 before starting preparatory work. The aim, of preparing a substrate for coating applications, is to roughen the surface, remove weak layers, contaminants, dirt, debris and present a solid, clean, dry substrate for the primer. If unsure as to the level of preparation needed contact Polymer Nation at techservice@polymernation.com
Product Details
Name
F-41 SLQ
Category
Kit Yield in Gallons
N/A
Number of Mixes Per Kit
1
A 1 mix kit consists of 2 gal A, 1 gal B, 1-50 LB. bag of PN 1321 F.
Number of Components
3
Mix Ratio Liquids by Volume
2:1
It is always preferred to mix the entire kit, whenever possible, to avoid off-ratio mixtures
Ideal Application Temperatures
60F-90F
Verify that substrate temperature is above 5 degrees of dewpoint during application and cure of material to avoid a potential amine blush
Mixed Viscosity in cP@25C/77F
600-700
Warmer temperatures will reduce viscosity and lower temperatures will increase viscosity
Gel Time
60 min.
Warmer temperatures will decrease gel time and lower temperatures will increase gel time
Dry to Touch
5-6 Hours
Warmer temperatures will reduce time and colder temperatures will increase time
Through Dry
10-12 Hours
Warmer temperatures will reduce time and colder temperatures will increase time
Dry to Walk
15 Hours
Warmer temperatures will reduce time and colder temperatures will increase time
Dry to Lightly Use
24 Hours
Warmer temperatures will reduce time and colder temperatures will increase time
Full Cure
7 Days
Warmer temperatures will reduce time and colder temperatures will increase time
Shore Hardness at 24 Hours
D65
Shore Hardness at 7 Days
D78
Warmer temperatures will shorten time to reach full hardness
Gloss @ 60 Degree Angle
90+
Not top coated. See Gloss data for selected top coat if required
VOC’s of Mixed Material
<50g/L
EPA Method 24
Color Scale per ASTM D1500
.5-1.0
Clear to slightly amber
Solids by Volume Mixed
100%
Storage
60F-90F
Store material between 60-90 degrees F in a protected dry location.
Odor
Subtle
Application Thickness in Mils
N/A
Coverage Per Mix
Each mix will cover 155 sq. ft. at 1/16″ theoretical coverage. A waste factor of 10% should be contemplated
Disposal
Dispose of material, containers, solvents, etc.per Federal, State and local guideline, rules and laws
Available Colors
System color is generated by the combination of aggregate blends.
Mixing & Installation
A mixture consists of 2 gal A, 1 gal B and 50 LB. of C (PN 1321 F). Combine part A and B into a single container, large enough to accept the entire kit (1 mix equals 6.5 gallons when Part C is added). Premix liquids at 350 RPM for 1 minutes. Pour Part C (PN 1321 F) into the mixed resin and continue mixing until a homogenous slurry is achieved (2-3 minutes usually), making sure not to introduce excessive air into the solution. Pour material on to floor and spread to desired thickness using a screed rake or notched squeegee. Once material has leveled, back roll with a spiked roller to aid in the release of trapped air. Whenever possible, work the shorter distance not the longer as this will help keep a fresh edge and make for easier blending. Temperature should be descending , not ascending during application and cure of slurry. This is critical whenever a broadcast will not be cast into the wet slurry. Recoat within 24 hours. Clean tools with a solvent similar to Xylene or Acetone.
Other Product Names
Polymer Nation believes the information contained herein to be true and accurate. Information contained herein is for evaluation purposes only.
Product HIghlights
Exceptional Performance, Durability, and Safety in Every Application
.png)
Most commonly Serviced Markets
Although most our products can be used on any market, we see some common trends between certain products and certain markets.
Available Colors
If you don't see a color you like here, some custom colors can be available upon request. Please contact us for more details!
.jpg)
Product Documentation
PRODUCT PDF.png)
.png)
