Category:
Wall Products
W-80
W-80 Epoxy Pigmented Wall Coating
About the product
Product Overview
W-80 consist of a high viscosity, nonylphenol-free, epoxy resin (E2W) and a thickened, cycloaliphatic amine reactant (H3). This combination achieves a rheology that makes it easy to spread but also fast to return to its resting state.
Uses
W-80 is most often used to coat vertical substrates that require a high-build, high-performance, material that will not run or sag. It can also be used as a pigmented grout coat on aggregate-filled mortar on coving and as a base and saturant coat for imbedding fiberglass and carbon-fiber sheeting.
Preparation
The coating installer should fully read and understand ICRI310.2R-2013 and OSHA 29 CFR 1926.1153 before starting preparatory work. The aim, of preparing a substrate for coating applications, is to roughen the surface, remove weak layers, contaminants, dirt, debris and present a solid, clean, dry substrate for the primer. If unsure as to the level of preparation needed contact Polymer Nation at techservice@polymernation.com
Product Details
For the most up-to-date product details, please view the Product Spec PDF below
PRODUCT PDFName
W-80
Category
Wall Products
Packaging
1.5 & 3 Gallons
Material can be supplied in larger packaging upon request and with minimum quantities
Number of Mixes Per Kit
N/A
N/A
Number of Components
2
1-2 gallon container of Part A and 1-1 gallon container of Part B
Mix Ratio Liquids by Volume
2:1
It is always preferred to mix the entire kit, whenever possible, to avoid off-ratio mixtures
Ideal Application Temperatures
60-85°F
Verify that substrate temperature is above 5 degrees of dewpoint during application and cure of material to avoid a potential amine blush
Mixed Viscosity in cP@25C/77F
4500-5000 cP
Warmer temperatures will reduce viscosity and lower temperatures will increase viscosity
Working Time
30-45 min
Gel Time
50 min.
Warmer temperatures will decrease gel time and lower temperatures will increase gel time
Dry to Touch
5 Hours
Warmer temperatures will reduce time and colder temperatures will increase time
Through Dry
8-12 hrs
Warmer temperatures will reduce time and colder temperatures will increase time
Dry to Walk
12 Hours
Warmer temperatures will reduce time and colder temperatures will increase time
Dry to Lightly Use
16-24 hrs
Warmer temperatures will reduce time and colder temperatures will increase time
Full Cure
7 Days
Warmer temperatures will reduce time and colder temperatures will increase time
Shore Hardness at 24 Hours
65
Shore D
Shore Hardness at 7 Days
75-80
Shore D
Gloss @ 60 Degree Angle
85-90
Applying material close to dew point will decrease gloss and may result in an amine blush
VOC’s of Mixed Material
Near zero; <50 g/L
EPA Method 24
Color Scale per ASTM D1500
.5-1.0
Clear to slightly amber before filler is introduced
Solids by Volume Mixed
100%
N/A
Storage
60F-90F
Store material between 60-90 degrees F in a protected dry location.
Odor
Very Subtle
Measuring odor offensiveness is difficult so experience with chemicals has been consulted here
Application Thickness in Mils
8-20 mils
N/A
Coverage Per Mix
80-200 sq.ft./gal
Disposal
Dispose of material, containers, solvents, etc. per Federal, State and local guideline, rules and laws
N/A
Available Colors
White, Light Gray, Warm Sun
Contact Polymer Nation for specialty colors
Mixing & Installation
See Technical Data Sheet or contact your local Polymer Nation Distributor
Other Product Names
Polymer Nation believes the information contained herein to be true and accurate. Information contained herein is for evaluation purposes only.
Product HIghlights
Exceptional Performance, Durability, and Safety in Every Application
.png)
Most commonly Serviced Markets
Although most our products can be used on any market, we see some common trends between certain products and certain markets.
Available Colors
If you don't see a color you like here, some custom colors can be available upon request. Please contact us for more details!
.png)
Product Documentation
PRODUCT PDF.png)
.png)
