Category:
Epoxies
P-30
P-30 Epoxy Grouting/Primer
About the product
Product Overview
P-30 consist of a high viscosity, nonylphenol-free, epoxy resin (E2) and a thickened, cycloaliphatic amine reactant (H3). This combination achieves a rheology that makes it easy to spread but also fast to return to its resting state.
Uses
P-30 is most often used to fill porous surfaces-like trowel applied epoxy flooring and coving and as a concrete block filler. It can also be used as a troweling paste to assist in the application of aggregate-filled mortar on coving and vertical substrates.
Preparation
The coating installer should fully read and understand ICRI310.2R-2013 and OSHA 29 CFR 1926.1153 before starting preparatory work. The aim, of preparing a substrate for coating applications, is to roughen the surface, remove weak layers, contaminants, dirt, debris and present a solid, clean, dry substrate for the primer. If unsure as to the level of preparation needed contact Polymer Nation at techservice@polymernation.com
Product Details
Name
P-30
Category
Epoxies
Kit Yield in Gallons
3
Material can be supplied in larger packaging upon request and with minimum quantities
Number of Mixes Per Kit
N/A
N/A
Number of Components
2
1-2 gallon container of Part A and 1-1 gallon container of Part B
Mix Ratio Liquids by Volume
2:1
It is always preferred to mix the entire kit, whenever possible, to avoid off-ratio mixtures
Ideal Application Temperatures
60F-90F
Verify that substrate temperature is above 5 degrees of dewpoint during application and cure of material to avoid a potential amine blush
Mixed Viscosity in cP@25C/77F
4500 +/- 500
Warmer temperatures will reduce viscosity and lower temperatures will increase viscosity
Gel Time
45 min.
Warmer temperatures will decrease gel time and lower temperatures will increase gel time
Dry to Touch
4 Hours
Warmer temperatures will decrease gel time and lower temperatures will increase gel time
Through Dry
8 Hours
Warmer temperatures will decrease gel time and lower temperatures will increase gel time
Dry to Walk
12 Hours
Warmer temperatures will decrease gel time and lower temperatures will increase gel time
Dry to Lightly Use
24 Hours
Warmer temperatures will decrease gel time and lower temperatures will increase gel time
Full Cure
7 Days
Warmer temperatures will decrease gel time and lower temperatures will increase gel time
Shore Hardness at 24 Hours
D65
Warmer temperatures will increase hardness
Shore Hardness at 7 Days
D78
Warmer temperatures will shorten time to reach full hardness
Gloss @ 60 Degree Angle
80-85
Applying material close to dew point will decrease gloss and may result in an amine blush
VOC’s of Mixed Material
<50g/L
EPA Method 24
Color Scale per ASTM D1500
.5-1.0
Clear to slightly amber before filler is introduced
Solids by Volume Mixed
100%
N/A
Storage
60F-90F
Store material between 60-90 degrees F in a protected dry location.
Odor
Subtle
Measuring odor offensiveness is difficult so experience with chemicals has been consulted here
Application Thickness in Mils
12-20 mils depending on porosity of substrate
N/A
Coverage Per Mix
Disposal
Dispose of material, containers, solvents, etc. per Federal, State and local guideline, rules and laws
N/A
Available Colors
Clear
N/A
Mixing & Installation
Combine all of part A and B into a single container, large enough to accept the entire kit. Mix at 350 RPM for 2-3 minutes using an appropriate mixing blade and making sure not to introduce excessive air into the solution. If using as a block filler- pour content into a large rolling pan and roll with a 9″ wide, 5/8″ nap roller cover. If using as a grout coat, pour the entire content from the container onto the floor and using a non-marking, flat squeegee, apply even pressure to force material into the pores and cavities being careful not to leave tails that will need to be removed once cured. Recoat within 24 hours. Clean tools with a solvent similar to Xylene or Acetone.
Other Product Names
Polymer Nation believes the information contained herein to be true and accurate. Information contained herein is for evaluation purposes only.
Product HIghlights
Exceptional Performance, Durability, and Safety in Every Application
.png)
Most commonly Serviced Markets
Although most our products can be used on any market, we see some common trends between certain products and certain markets.
Available Colors
If you don't see a color you like here, some custom colors can be available upon request. Please contact us for more details!
Product Documentation
PRODUCT PDF.png)
.png)
