Category:
Epoxies
P-03
P-03 1K Epoxy Concrete Primer
About the product
Product Overview
P-03 is a two component, waterborne epoxy primer/sealer. It has excellent adhesion to concrete and provides fast dry and early hardness properties.
Uses
P-03 is most often used as a concrete floor primer but can also be used as a vertical primer on concrete and wallboard. It has moderate UV resistance, compared with most epoxies and has very low odor. It is easy to apply and provides an excellent base layer for subsequent coatings of all types.
Preparation
The coating installer should fully read and understand ICRI310.2R-2013 and OSHA 29 CFR 1926.1153 before starting preparatory work. The aim, of preparing a substrate for coating applications, is to roughen the surface, remove weak layers, contaminants, dirt, debris and present a solid, clean, dry substrate for the primer. If unsure as to the level of preparation needed contact Polymer Nation at techservice@polymernation.com
Product Details
Name
P-03
Category
Epoxies
Kit Yield in Gallons
2.5, 25
Material can be supplied in larger packaging upon request and with minimum quantities
Number of Mixes Per Kit
N/A
N/A
Number of Components
2
N/A
Mix Ratio Liquids by Volume
1A:4B
Stir the entire content prior to use to insure complete and even mixture
Ideal Application Temperatures
60F-90F
Verify that substrate temperature is above 5 degrees of dewpoint during application and cure of material to avoid a potential amine blush
Mixed Viscosity in cP@25C/77F
600-700
Warmer temperatures will reduce viscosity and lower temperatures will increase viscosity
Gel Time
30 min.
Warmer temperatures will decrease gel time and lower temperatures will increase gel time
Dry to Touch
60 min.
Warmer temperatures will decrease gel time and lower temperatures will increase gel time
Through Dry
4 Hours
Warmer temperatures will decrease gel time and lower temperatures will increase gel time
Dry to Walk
6 Hours
Warmer temperatures will decrease gel time and lower temperatures will increase gel time
Dry to Lightly Use
24 Hours
Warmer temperatures will decrease gel time and lower temperatures will increase gel time
Full Cure
7 Days
Warmer temperatures will decrease gel time and lower temperatures will increase gel time
Shore Hardness at 24 Hours
20
Warmer temperatures will increase hardness
Shore Hardness at 7 Days
40
Warmer temperatures will shorten time to reach full hardness
Gloss @ 60 Degree Angle
55-60
Applying material close to dew point will decrease gloss and may result in an amine blush
VOC’s of Mixed Material
<50 g/L
EPA Method 24
Color Scale per ASTM D1500
N/A
Clear to slightly amber before colorants are introduced
Solids by Volume Mixed
>52%
N/A
Storage
60F-90F
Store material between 60-90 degrees F in a protected dry location.
Odor
Subtle
Measuring odor offensiveness is difficult so experience with chemicals has been consulted here
Application Thickness in Mils
4-8
N/A
Coverage Per Mix
Disposal
Dispose of material, containers, solvents, etc. per Federal, State and local guideline, rules and laws
N/A
Available Colors
White, Light Gray and Warm Sun
N/A
Mixing & Installation
Stir entire container at 350 RPM for 2-3 minutes using an appropriate mixing blade and making sure not to introduce excessive air into the solution. Apply using airless equipment, squeegee and brush and roll techniques. Recoat within 24 hours. Clean tools with a solvent similar to Xylene or Acetone.
Other Product Names
Polymer Nation believes the information contained herein to be true and accurate. Information contained herein is for evaluation purposes only.
Product HIghlights
Exceptional Performance, Durability, and Safety in Every Application
.png)
Most commonly Serviced Markets
Although most our products can be used on any market, we see some common trends between certain products and certain markets.
.jpg)
Available Colors
If you don't see a color you like here, some custom colors can be available upon request. Please contact us for more details!
Product Documentation
PRODUCT PDF.png)
.png)
