Category:
F-41
F-41 Clear UV Resistant Epoxy Floor Coating
About the product
Product Overview
F-41 consist of a low viscosity, nonylphenol-free, clear, UV resistant epoxy resin (E5) with our UV resistant, cycloaliphatic amine reactant (H4). This combination achieves a UV resistant, clear epoxy with good flow and leveling, characteristics. The cured material has good broad-range chemical resistance as well as good abrasion and impact resistance.
Uses
F-41 is most often used as a clear topcoat for resinous concrete flooring projects that may experience higher UV exposure than is found in most interior environments.
Preparation
The coating installer should fully read and understand ICRI310.2R-2013 and OSHA 29 CFR 1926.1153 before starting preparatory work. The aim, of preparing a substrate for coating applications, is to roughen the surface, remove weak layers, contaminants, dirt, debris and present a solid, clean, dry substrate for the primer. If unsure as to the level of preparation needed contact Polymer Nation at techservice@polymernation.com
Product Details
Name
F-41
Category
Kit Yield in Gallons
3, 15, 165
Special packaging is available based on size of order and time constraints
Number of Mixes Per Kit
N/A
N/A
Number of Components
2
N/A
Mix Ratio Liquids by Volume
2:1
It is always preferred to mix the entire kit, whenever possible, to avoid off-ratio mixtures
Ideal Application Temperatures
60F-90F
Verify that substrate temperature is above 5 degrees of dewpoint during application and cure of material to avoid a potential amine blush
Mixed Viscosity in cP@25C/77F
600-700
Warmer temperatures will reduce viscosity and lower temperatures will increase viscosity
Gel Time
60 min.
Warmer temperatures will decrease gel time and lower temperatures will increase gel time
Dry to Touch
5-6 Hours
Warmer temperatures will reduce time and colder temperatures will increase time
Through Dry
10-12 Hours
Warmer temperatures will reduce time and colder temperatures will increase time
Dry to Walk
15 Hours
Warmer temperatures will reduce time and colder temperatures will increase time
Dry to Lightly Use
24 Hours
Warmer temperatures will reduce time and colder temperatures will increase time
Full Cure
7 Days
Warmer temperatures will reduce time and colder temperatures will increase time
Shore Hardness at 24 Hours
D65
Warmer temperatures will increase hardness
Shore Hardness at 7 Days
D78
Warmer temperatures will shorten time to reach full hardness
Gloss @ 60 Degree Angle
90+
Applying material close to dew point will decrease gloss and may result in an amine blush
VOC’s of Mixed Material
<50g/L
EPA Method 24
Color Scale per ASTM D1500
.5-1.0
Clear to slightly amber
Solids by Volume Mixed
100%
N/A
Storage
60F-90F
Store material between 60-90 degrees F in a protected dry location.
Odor
Subtle
Measuring odor offensiveness is difficult so experience with chemicals has been consulted here
Application Thickness in Mils
As a topcoat 10-16
N/A
Coverage Per Mix
N/A
Disposal
Dispose of material, containers, solvents, etc.per Federal, State and local guideline, rules and laws
N/A
Available Colors
Clear and Color Packs
N/A
Mixing & Installation
Combine all of part A and B into a single container, large enough to accept the entire kit. Mix at 350 RPM for 2-3 minutes using an appropriate mixing blade and making sure not to introduce excessive air into the solution. Pour the entire content from the container onto the floor and follow normal squeegee and back roll techniques. Recoat within 24 hours. Clean tools with a solvent similar to Xylene or Acetone.
Other Product Names
Polymer Nation believes the information contained herein to be true and accurate. Information contained herein is for evaluation purposes only.
Product HIghlights
Exceptional Performance, Durability, and Safety in Every Application
.png)
.png)
Most commonly Serviced Markets
Although most our products can be used on any market, we see some common trends between certain products and certain markets.
.jpg)
Available Colors
If you don't see a color you like here, some custom colors can be available upon request. Please contact us for more details!
Product Documentation
PRODUCT PDF.png)
.png)
