Category:
SP-10
SP-10 Flexible Joint Filler
About the product
Product Overview
SP-10 is a flexible aromatic urethane that has extreme tensile strength and elongation while maintaining a mid-level D shore hardness. It is easy to install and can be shaved or filled to precision without the need to shave. It is designed to allow concrete joints to move freely while reinforcing the shoulder walls of control and expansion joints in concrete.
Uses
SP-10 is primarily used as a pigmented joint filler. It can also be used as a flexible pore filler on foam and as a patching material in soft floor applications.
Preparation
The coating installer should fully read and understand ICRI310.2R-2013 and OSHA 29 CFR 1926.1153 before starting preparatory work. The aim, of preparing a substrate for coating applications, is to roughen the surface, remove weak layers, contaminants, dirt, debris and present a solid, clean, dry substrate for the primer. If unsure as to the level of preparation needed contact Polymer Nation at techservice@polymernation.com
Product Details
Name
SP-10
Category
Kit Yield in Gallons
1
A 1 mix kit consists of .86 gal A and .14 gal B
Number of Mixes Per Kit
N/A
Number of Components
2
Mix Ratio Liquids by Volume
Not Provided
Do not split kits.
Ideal Application Temperatures
60F-90F
Verify that substrate temperature is above 5 degrees of dewpoint during application and cure of material to avoid a potential amine blush
Mixed Viscosity in cP@25C/77F
2500
Warmer temperatures will reduce viscosity and lower temperatures will increase viscosity
Gel Time
23 min.
Warmer temperatures will decrease gel time and lower temperatures will increase gel time
Dry to Touch
2.5 Hours
Warmer temperatures will reduce time and colder temperatures will increase time
Through Dry
4 Hours
Warmer temperatures will reduce time and colder temperatures will increase time
Dry to Walk
8 Hours
Warmer temperatures will reduce time and colder temperatures will increase time
Dry to Lightly Use
12 Hours
Warmer temperatures will reduce time and colder temperatures will increase time
Full Cure
7 Days
Warmer temperatures will reduce time and colder temperatures will increase time
Shore Hardness at 24 Hours
D20
Warmer temperatures will increase hardness
Shore Hardness at 7 Days
D45
Warmer temperatures will shorten time to reach full hardness
Gloss @ 60 Degree Angle
82-85
Applying material close to dew point will decrease gloss and may result in an amine blush
VOC’s of Mixed Material
<8 g/L
EPA Method 24
Color Scale per ASTM D1500
N/A
Solids by Volume Mixed
100%
Storage
60F-90F
Store material between 60-90 degrees F in a protected dry location.
Odor
Very Subtle
Application Thickness in Mils
N/A
Coverage Per Mix
Each mix will fill 308 LF of 1/4″ X 1/4″ joints theoretical coverage. A waste factor of 10-15% should be contemplated
Disposal
Dispose of material, containers, solvents, etc.per Federal, State and local guideline, rules and laws
Available Colors
Light Gray, Beige, Tile Red, Black
Mixing & Installation
Combine all of part A and B into a single container, large enough to accept the entire kit. Mix at 350 RPM for 2-3 minutes using an appropriate mixing blade and making sure not to introduce excessive air into the solution. Pour the entire content from a plastic container, that can be deformed at the opening to make a pour spout, and pour into the joint (backer rod in 50% compression are dry sand filling half joint depth is recommended in the base of the joint prior to filling). Material that overflows the joint can be scraped with a sharp blade as soon as the material has taken its initial set. Recoat within 24 hours. Clean tools with a solvent similar to Xylene or Acetone.
Other Product Names
Polymer Nation believes the information contained herein to be true and accurate. Information contained herein is for evaluation purposes only.
Product HIghlights
Exceptional Performance, Durability, and Safety in Every Application
.png)
Most commonly Serviced Markets
Although most our products can be used on any market, we see some common trends between certain products and certain markets.
Available Colors
If you don't see a color you like here, some custom colors can be available upon request. Please contact us for more details!
Product Documentation
PRODUCT PDF.png)
.png)
