Category:
F-52
F-52 AD ALIPHATIC URETHANE CONCRETE DRESSING
About the product
Product Overview
F-52 AD is a proprietary formula on that allows longer working me with a snap-cure. It combines our water-based urethane resin and aliphatic hardener with our proprietary blend of portland cement, lime and fillers (PN 1352 D). It has been formulated to work with our TD and SL systems to provide the highest degree of impact, UV resistance, and thermal shock resistance of any urethane concrete on the market. It’s low odor and easy application make it perfect for industrial and durable decorative applications.
Uses and Benefits
F-52 AD is most o en used as a topcoat for our TD and SL systems. It's low viscosity and tenacious bond to concrete make it an excellent prime/build coat for many decorative and industrial applications. F-52 AD can also be used as a primer when concrete floors exhibit high moisture transmission levels and can be applied to green concrete.
Preparation
The coating installer should fully read and understand ICRI310.2R-2013 and OSHA 29 CFR 1926.1153 before starting preparatory work. The aim, of preparing a substrate for coating applications, is to roughen the surface, remove weak layers, contaminants, dirt, debris and present a solid, clean, dry substrate for the primer. If unsure as to the level of preparation needed contact Polymer Nation at techservice@polymernation.com
Product Details
Name
F-52
Category
Kit Yield in Gallons
N/A
Number of Mixes Per Kit
1, 50
A 1 mix kit consists of 1.1 gal A, 0.75 gal B and 1-14 LB. bag of C. A 50 mix kit consists of 55 gal A, 37.5 gal B, 50-14 LB. bags C
Number of Components
3
Mix Ratio Liquids by Volume
1:1 see Mixing & Installation
Accuracy when mixing kits from bulk containers is critical. For mix ratio by weight contact Lab@polymerNation.com.
Ideal Application Temperatures
40F-80F
Mixed Viscosity in cP@25C/77F
300 A & B
Warmer temperatures will reduce viscosity and lower temperatures will increase viscosity
Gel Time
N/A
Warmer temperatures will decrease gel time and lower temperatures will increase gel time
Dry to Touch
2 Hours
Warmer temperatures will reduce time and colder temperatures will increase time
Through Dry
4 Hours
Warmer temperatures will reduce time and colder temperatures will increase time
Dry to Walk
6 Hours
Warmer temperatures will reduce time and colder temperatures will increase time
Dry to Lightly Use
24 Hours
Warmer temperatures will reduce time and colder temperatures will increase time
Full Cure
7 Days
Warmer temperatures will reduce time and colder temperatures will increase time
Shore Hardness at 24 Hours
D70
Warmer temperatures will increase hardness
Shore Hardness at 7 Days
D78
Warmer temperatures will shorten time to reach full hardness
Gloss @ 60 Degree Angle
30-40
VOC’s of Mixed Material
<50g/L
EPA Method 24
Color Scale per ASTM D1500
N/A
Milky appearance when mixed before colorants are introduced
Solids by Volume Mixed
>95%
Storage
60F-90F
Store material between 60-90 degrees F in a protected dry location.
Odor
Subtle
Application Thickness in Mils
N/A
Coverage Per Mix
Each mix will cover 251 sq. ft. at 20 mils theoretical coverage. A waste factor of 10-15% should be contemplated
Disposal
Dispose of material, containers, solvents, etc.per Federal, State and local guideline, rules and laws
Available Colors
Natural, Tile Red, Light Gray, Medium Gray, Dark Gray, Black
Mixing & Installation
A mixture consists of 1.1 gal A, 0.75 gal B and 14 LB. of C (PN 1352 D). Combine part A and B into a single container, large enough to accept the entire kit (1 mix equals 3.14 gallons when Part C is added). Premix liquids at 350 RPM for 1 minutes using an appropriate mixing blade or mixing machine. Pour material on to floor and spread to desired thickness using squeegee and back roll techniques. If a broadcast has been selected, begin broadcasting evenly across the floor, following the same order in which the coating was installed. Whenever possible, work the shorter distance not the longer as this will help keep a fresh edge and make for easier blending. Recoat within 24 hours. Clean tools with a solvent similar to Xylene or Acetone.
Other Product Names
Polymer Nation believes the information contained herein to be true and accurate. Information contained herein is for evaluation purposes only.
Product HIghlights
Exceptional Performance, Durability, and Safety in Every Application
Most commonly Serviced Markets
Although most our products can be used on any market, we see some common trends between certain products and certain markets.
Available Colors
If you don't see a color you like here, some custom colors can be available upon request. Please contact us for more details!
Product Documentation
PRODUCT PDF.png)
.png)
