Category:
SP-17
SP-17 Rapid Patch Liquid
About the product
Product Overview
SP-17 combines our fastest setting polyaspartic with our proprietary Iso blend to create a rapid pour and patch system. By incorporating a variety of fillers and aggregates the user can achieve a patching material that is ready for grinding in 1 hour.
Uses
SP-17 is most often used to patch concrete holes, cracks, divots and non-moving joints when time is too limited for our SP-15 patching material.
Preparation
The coating installer should fully read and understand ICRI310.2R-2013 and OSHA 29 CFR 1926.1153 before starting preparatory work. The aim, of preparing a substrate for coating applications, is to roughen the surface, remove weak layers, contaminants, dirt, debris and present a solid, clean, dry substrate for the primer. If unsure as to the level of preparation needed contact Polymer Nation at techservice@polymernation.com
Product Details
Name
SP-17
Category
Kit Yield in Gallons
N/A
Number of Mixes Per Kit
Depends on mix size
A 1 mix kit consists of 1 part A, 1 part B and select aggregate or powder. See Mixing and Installation below.
Number of Components
2
Mix Ratio Liquids by Volume
2:1 see Mixing & Installation
Ideal Application Temperatures
50F-80F
Mixed Viscosity in cP@25C/77F
300 A & B
Warmer temperatures will reduce viscosity and lower temperatures will increase viscosity
Gel Time
5 min.
Warmer temperatures will decrease gel time and lower temperatures will increase gel time
Dry to Touch
.5 Hours
Warmer temperatures will reduce time and colder temperatures will increase time
Through Dry
.75 Hours
Warmer temperatures will reduce time and colder temperatures will increase time
Dry to Walk
2 Hours
Warmer temperatures will reduce time and colder temperatures will increase time
Dry to Lightly Use
3 Hours
Warmer temperatures will reduce time and colder temperatures will increase time
Full Cure
2 Days
Warmer temperatures will reduce time and colder temperatures will increase time
Shore Hardness at 24 Hours
D65
Warmer temperatures will increase hardness
Shore Hardness at 7 Days
D81
Warmer temperatures will shorten time to reach full hardness
Gloss @ 60 Degree Angle
30-40
Applying material close to dew point will decrease gloss and may result in an amine blush
VOC’s of Mixed Material
<50g/L
EPA Method 24
Color Scale per ASTM D1500
.5-1.0
Clear to slightly amber before filler is introduced
Solids by Volume Mixed
100%
Storage
60F-90F
Store material between 60-90 degrees F in a protected dry location.
Odor
Subtle
Application Thickness in Mils
N/A
Coverage Per Mix
N/A
Disposal
Dispose of material, containers, solvents, etc.per Federal, State and local guideline, rules and laws
Available Colors
This material is available in clear
Mixing & Installation
This material is extremely fast reacting. Only mix what can be poured out in 3-4 minutes from initial mixing. A starting point mixture may consist of 2 FL. OZ. A, 2 FL. OZ. B and 245 grams of aggregate (about 5 FL. OZ.). Aggregate size and the fluidity of the mixed material is based upon user preference and application parameters. Combine 1 part A and 1 part B into a single container, large enough to accept the entire kit. Mix liquids at 200 RPM for 30 seconds using an appropriate mixing blade. Immediately add the aggregate into the mixed resin and agitate for 1 minute. Immediately pour the entire mixed content from the container into the area to be filled. Patch may be shaved in 30 min. to 1 hr. and ground after 2 hours. Clean tools with a solvent similar to Xylene or Acetone.
Other Product Names
Polymer Nation believes the information contained herein to be true and accurate. Information contained herein is for evaluation purposes only.
Product HIghlights
Exceptional Performance, Durability, and Safety in Every Application
.png)
Most commonly Serviced Markets
Although most our products can be used on any market, we see some common trends between certain products and certain markets.
Available Colors
If you don't see a color you like here, some custom colors can be available upon request. Please contact us for more details!
.jpg)
Product Documentation
PRODUCT PDF.png)
.png)
